高电阻小电压测试装置仪（耐弧光测试装置仪）-（测算机有效控制）

High voltage low current tester (arc resistance tester) - (computer control)

好产产品明称称：耐电弧试验机

Product name: electric arc resistance tester

成品型号规格：NDH-A

Product model: NDH - A

达到标准规范：GB/T 1411-2002《膏状接地材质耐高低平电压电流弧光蓄电池充电的试验台》（就是指IEC  61621-1997）及ASTM D495等原则的需求结构设计制造出的，并合乎IEC 149、UL 746A等校正工艺

Meet the standards: GB/T 1411-1411 "solid insulating material resistant to high voltage low current arc discharge test" (equivalent to IEC 61621-1997) and the requirements of standards such as ASTM D495 design and manufacturing, and conform to the IEC 149, UL 746 a test method, etc

一 概述

一An overview of the

主要应用范围之内及功用：

本实验室检测机是如果根据软件应主要用于同步电机、电子元件和小型电子元件等职业的水电工用塑、树酯胶和隔绝漆等隔绝的原原材料的耐电孤机械性能方面评选，主主要用于液体隔绝的原原材料如：塑、聚酰亚胺膜、树酯、云母片、卫浴陶瓷、夹丝玻璃、隔绝油、隔绝漆、瓦楞纸板等材质的耐电孤机械性能方面软件测试；

本耐压机由计算出来机把控正常运作，应该显现所选科学工作室设计心态及科学工作室设计准确时间，科学工作室设计停止后并保留所选科学工作室设计动态数据，并可打印机.规则科学试验该报告。

Main scope of application and features:

This machine is in accordance with the applied in motor, electrical appliances and household appliances and other industries with varnish insulation materials such as plastic, resin adhesive and the arc resistance evaluation, the main used for solid insulating material such as plastic, film, resin, mica, ceramic, glass, insulating oil, insulating paint, such as cardboard medium arc resistance test;

This testing machine controlled by computer operation, can display the current experimental condition and experimental time, after the experiment, and save the current experimental data and can be printed. Standard experiment report 

二 功能特点

1 该机为两边分立式框架，上侧为运营模式，上侧为耐压试验仪。

2 本品牌按照*新智力调控水平，经由选定 系统（IEC或ASTM）可定时开展耐压试验，并在手提电脑手机上现示可靠性试验具体步骤和报告单。

3 **性能参数非常好，抗扰乱专业能力强，检验可靠性强，精密度更高。

二：Functional features：

1 this machine is up and down a body structure, lower for the operating system, the upper part of test cases.

2 this product USES the latest intelligent control technology, through the selection process (IEC) or ASTM test can be automatically, and displayed on the computer and the test process and results.

3 good safety performance, strong anti-interference ability, high test precision. 

三 主要技术参数

1 弧光通断耗时测量误差：乘以 ±10ms

2 调压器容积：2kVA

3 额定容量耐压电阻值：12.5kV

4 现场实验电压值误差：±3%

5 交流电有效控制gps精度：±10%  交流电检测控制精度：1.5%

6 电极材料对坯料的压力：（0.5±0.05）N

7 电极装修材料装修材料：钨棒

8 电级时间：（6.35±0.1）mm（IEC）

               （6.0±0.1）mm（ASTM）

9 的使用的温度湿度表：（23±2）℃

10 安全使用环境温度：（50±5）%

11 电：220V±5%  50Hz  10A

12 试验台    方法步骤：   国家标准下载/美标/10 mA 连续不断/20 mA 多次/30 mA接连/40 mA连继

13 经过多次实验发现编译程序详细：

Three main technical parameters：

Error: 1 arc on-off time less than plus or minus 10 ms

Transformer capacity: 2 kva

3 test voltage rating: 12.5 kV

4: test voltage accuracy + / - 3%

5 current control accuracy: plus or minus 10% current measuring accuracy: 1.5%

6 electrode pressure on sample: (0.5 + 0.5) N

7 electrode materials: tungsten rods

8 electrode distance: 6.35 + / - 0.1 mm (6.0 + 0.1) mm (IEC) (ASTM)

9 using the environment temperature (23 + 2) ℃

10 use environment humidity: (50 + 5) %

Power supply: 220 v + 5% for 50 hz 10 a

Test method: beautiful mark / 10 gb / 30 mA mA continuous / 20 mA continuous/continuous / 40 mA continuous

13 test procedure is as follows:

Procedures section of the arc current

MA arc on-off time s the program s test total duration time s

IEC 61621 ASTM D495

1 1/8 10 s on 7/8 s broken 1/4 7/4 break 60 s 60 s

2 10 1/4 "s pass 3/4 s 1/4 3/4 break 60 s 120 s

3 to 10 1/4 "s make a quarter s break a quarter of a quarter break 60 s 180 s

4 consecutive 10 to 60, 240

5 20 consecutive 60, 300

30 consecutive 6 to 60, 360

7 consecutive 40 to 60, 420 

四  配置

Four configuration：

Serial number name number note

01 arc resistance tester

02 a electrode system

03 electrode bearing a set

04 a set of power cable

05 ground put a rod

06 milliammeter current one

7 a set of computer measurement and control software

08 specimen holder a

09 electrode distance standard 2 blocks

Standard 2 blocks of 10 Angle

11 ceramic pieces 2 pieces

12 one brand inkjet printer

13 1 computer brand

14 1 instruction manual

15 1 certificate

五 產品技术参数：

NDH-A    耐弧光检测仪-微机有效控制

NDH-B    耐电弧放电现场实验仪-手触屏操作

Five product model:

NDH - A arc resistance tester - microcomputer control

NDH - B arc resistance tester - touch screen control
ASTMD495耐高压低电流电弧放电试验机详情可以随时来电咨询！